Skip to content Skip to footer

Low Water Pressure at Home: Causes and Fixes

Tap with low water pressure

The shower barely wets you, the kitchen tap takes forever to fill the kettle, and upstairs is even worse than downstairs. Low water pressure is one of those problems people put up with for months because it never quite stops working. In most homes there is a clear reason for it, and many of the causes are quick to fix once you know where to look.

Is it one tap or the whole house?

Start here, because it narrows things down straight away. Turn on the cold taps in the kitchen and bathroom one by one and compare them.

  • Only one tap or shower is weak: the problem is almost certainly at that fitting.
  • Only the hot water is weak: look at the boiler, cylinder or hot water pipework.
  • Everything is weak: the cause is at the stopcock, the supply pipe or the mains.

When low water pressure is at one tap or shower

A blocked aerator

Most taps have a small mesh filter, called an aerator, screwed into the spout. Limescale and grit collect in it, especially with London’s hard water. Unscrew it, soak it in white vinegar for an hour, rinse and refit. The difference is often instant.

A scaled-up shower head

Low water pressure in the shower is often the same problem. Soak the head in vinegar overnight, then clear any blocked holes with an old toothbrush. If the head is old and heavily scaled, replacing it can be the easier option.

A partly closed isolation valve

Under sinks and behind toilets there are small valves with a screw slot. If one has been turned partly off during a repair, the flow drops. Use a flat screwdriver to turn it so the slot lines up with the pipe.

When the whole house has low water pressure

Check the stopcock

The internal stopcock, often under the kitchen sink, should be fully open. After plumbing work, it is sometimes left half closed. Turn it fully anticlockwise, then back a quarter turn so it does not seize.

Ask the neighbours

If the street has the same problem, it is likely work on the mains or a burst nearby. In that case there is nothing to fix inside your home, and it usually returns to normal once the work is finished.

Old or narrow supply pipes

Many older London properties still have narrow or ageing supply pipes, sometimes even old lead pipework. Inside, they can be furred up with scale. This gives weak pressure throughout the house, worst when two taps run at once. Replacing the pipe is the long-term fix.

A hidden leak

If pressure has dropped suddenly and you can hear running water when every tap is off, or you see damp patches, a leak could be taking the water before it reaches your taps. This needs finding quickly, before it causes damage.

Low pressure on the hot side only

If the cold taps are fine but the hot side is weak, the cause is usually in the heating system. On a combi boiler, a blocked filter or scaled heat exchanger can restrict flow. With a gravity-fed cylinder, pressure depends on how high the cold water tank sits in the loft, so upstairs showers are often weak by design. A pump or an upgrade to a mains pressure system can fix that.

Flats and upper floors

In blocks of flats, top-floor flats often get weaker pressure, especially at busy times in the morning. Some buildings use booster pumps. If yours does and the pressure has dropped, the pump may need attention from the building’s management.

What not to do

  • do not fit a pump to an electric shower or a combi boiler without checking it is allowed
  • do not force a seized stopcock with a long bar, as old ones can snap
  • do not ignore a sudden drop in pressure, which can mean a leak

Getting low water pressure fixed

Simple fixes like cleaning an aerator or opening a valve take minutes. When the cause is old pipework, a hidden leak or the hot water system, it needs a plumber. CityPrime’s plumbing services cover water pressure problems, leak detection and pipe replacement in homes across London. For landlords, weak showers are a common tenant complaint, so it is worth sorting before it becomes a formal repair request.

Water pressure questions

What causes low water pressure in a house?

Common causes include blocked tap aerators and shower heads, a partly closed stopcock or valve, old or narrow supply pipes, leaks and work on the water mains. If only the hot side is weak, the cause is usually in the boiler or cylinder.

How can I increase water pressure at home?

Clean aerators and shower heads, make sure the stopcock and isolation valves are fully open, and check for leaks. If the supply pipe is old or narrow, replacing it is the long-term fix.

Why is my water pressure low upstairs?

With a gravity-fed system, pressure depends on the height of the cold water tank, so upstairs is often weaker. A pump or a mains pressure system can improve it.

Why has my water pressure suddenly dropped?

A sudden drop usually means work on the mains, a burst nearby or a leak in your property. Check with neighbours first, and look for damp patches or the sound of running water.

Can limescale cause low water pressure?

Yes. In hard water areas like London, limescale builds up in aerators, shower heads and pipes, and restricts the flow. Descaling fittings regularly helps.